公司新聞
攤鋪機作業時攤鋪面不平整的應對
來源：http://m.yuanchuodian.cn/ 日期：2022-11-25
攤鋪機在使用過程中，經常會出現各種大大小小的問題，今天濟南攤鋪機出租廠家就一起來分享一下攤鋪機作業時攤鋪面不平整的應對。
During the use of the paver, various problems, large and small, often occur. Today, the Jinan paver rental manufacturer would like to share with us how to deal with the uneven paving surface during the operation of the paver.
①加熱溫度（熨平板地板溫度120度為宜）；
① Heating temperature (the temperature of screed floor should be 120 ℃);
②熨平板的平整度（底板連接不平整，底板表面不平整）；
② Flatness of screed (uneven connection of base plate and uneven surface of base plate);
③夯錘的速度（夯錘速度過低，出現坑洞；過高，表面起臺）；
③ The speed of the rammer (if the rammer speed is too low, holes will appear; if it is too high, the surface will rise);
④行走速度過快，有離析；
④ The walking speed is too fast and there is segregation;
⑤螺旋高度不合適，有離析；
⑤ Improper spiral height and segregation;
⑥找平裝置安裝不正確（裝反、超出感應范圍等），起波浪；
⑥ The leveling device is installed incorrectly (installed reversely, out of the sensing range, etc.), causing waves;
⑦路基不平整，參照物不準確，攤鋪厚度不一致，造成路面發白，碾壓時產生推移。料溫過低，也會造成攤鋪面離析和開裂。
⑦ The subgrade is not smooth, the reference is not accurate, and the paving thickness is inconsistent, which causes the pavement to be white, and the rolling will cause displacement. If the material temperature is too low, it will also cause segregation and cracking of the paving surface.
應對辦法：
Countermeasures:
作業前檢查熨平板底板是否平整，底板是否粘連雜物，及時清理和調整；
Before operation, check whether the screed bottom plate is flat and whether there are sundries stuck on the bottom plate, and clean and adjust it in time;
在加熱溫度達到要求后，再進行攤鋪工作；
Paving shall be carried out after the heating temperature reaches the requirements;
在料斗、刮板倉、螺旋處噴灑柴油，防止產生油斑；
Spray diesel oil at hopper, scraper bin and screw to prevent oil stain;
正確設定夯錘與攤鋪速度，螺旋的高度以高過攤鋪面的兩倍高度為宜；
The tamping hammer and paving speed shall be set correctly, and the screw height shall be twice higher than the paving surface;
正確安裝找平儀（或平衡梁探頭高度與連線的位置）；
Correctly install the leveling instrument (or the position of the balance beam probe height and connecting line);
時刻注意觀察參照物是否準確；
Always observe whether the reference object is accurate;
當路基平整度落差過大時，應提前墊料處理。
When the drop of subgrade flatness is too large, padding treatment shall be carried out in advance.
攤鋪機作業時攤鋪面不平整的應對相關事項就講解到這里了，您對此有什么疑惑可以隨時來我們網站http://m.yuanchuodian.cn咨詢了解！
This is all for dealing with the unevenness of the paving surface during the operation of the paver. If you have any questions, please come to our website at any time http://m.yuanchuodian.cn Ask about it!
公司地址：濟南市商河縣賈莊鎮民營經濟創業園
公司名稱:永誠廣建公路材料（山東）有限公司 
備案號：