公司新聞
壓路機前輪支承件變形的修復方法
來源：http://m.yuanchuodian.cn/ 日期：2023-01-18
當靜壓壓路機發生無法啟動故障時，當時為了啟動該壓路機，在現場使用裝載機進行頂推啟動，結果造成該壓路機支承前輪的方框發生變形，前叉與立軸配合的軸套焊接處錯位，該壓路機無法使用。壓路機前輪支承件變形了怎么辦？有沒有好的修復方法呢？
When the static pressure roller failed to start, in order to start the roller, a loader was used to start it at the site. As a result, the box supporting the front wheel of the roller was deformed, and the front fork and the shaft sleeve welded with the vertical shaft were misaligned. The roller could not be used. What if the front wheel bearing of the roller is deformed? Is there a good repair method?
實際上通常修復該故障需將前輪方框、立軸與前叉拆解，但是這樣修理費時費力。為此，濟南壓路機出租廠家采用了以下簡易的恢復方法：
In fact, it is usually necessary to disassemble the front wheel box, vertical shaft and front fork to repair the fault, but such repair is time-consuming and laborious. To this end, Jinan roller rental manufacturer adopted the following simple recovery methods:
將前輪調整到正前方向;其次，將前輪、前輪方框及前叉橫梁用木料墊住，使其在轉動轉向盤時前輪不產生轉動;再次，轉動轉向盤，記住轉向盤旋轉總?cè)?shù)，轉到極限位置再轉回一半總?cè)?shù)，錯位的前叉與立軸配合的軸套便可回到正確位;然后，拆下前輪方框兩側的14只固定螺栓，用千斤頂將前輪方框頂起約400mm，使其離開前輪軸;，用電焊將立軸軸套焊接牢固，松去千斤頂，落下前輪叉，將前輪方框與前輪軸裝復。這樣做只需1個人便可將前輪方框變形調整到位。
Adjust the front wheels to the straight ahead direction; Secondly, cushion the front wheel, front wheel box and front fork crossbeam with wood to prevent the front wheel from rotating when turning the steering wheel; Again, turn the steering wheel, remember the total number of turns of the steering wheel, turn to the limit position and then turn back half of the total number of turns, and the misaligned front fork and the shaft sleeve fitted with the vertical shaft can return to the correct position; Then, remove the 14 fixing bolts on both sides of the front wheel box, and jack the front wheel box up about 400mm to make it leave the front wheel axle;, Weld the vertical shaft sleeve firmly with electric welding, loosen the jack, drop the front wheel fork, and reassemble the front wheel box and the front wheel shaft. In this way, only one person can adjust the deformation of the front wheel box in place.
此外一些注意事項要了解到，比如：
In addition, some precautions should be learned, such as:
短距離運送壓路機時，根據門道環境，壓路機可選取用高速自行開到工地。在遠距離運送壓路機時，壓路機使用平板拖車運送，在起吊和運送傍邊，使用機身上的寧靜鎖緊設備，將結構鎖逝世，防范機身和結構發生相對滾動，同時，壓路機應牢固地牢固在平板拖車上。
When transporting the roller in a short distance, according to the doorway environment, the roller can choose to drive to the construction site at high speed. When transporting the roller at a long distance, the roller shall be transported by flat trailer. At the side of lifting and transportation, the quiet locking device on the body shall be used to lock the structure to prevent the body and structure from rolling. At the same time, the roller shall be firmly fixed on the flat trailer.
壓路機如果擱置不用，須放出發動機水箱內的水，在冬氣冰冷的時期，每天工作結束后就應放掉。設置配備布置機器提示說，詳盡洗濯失時器上的污物和塵土，用火油擦拭各部件的外外貌和通通光滑孔并注一次油脂，對未涂漆的顯露部分應涂黃油或防銹膠。
If the roller is not used, the water in the engine water tank must be drained. In the cold winter, the water should be drained after the end of each day's work. The setting and arrangement of the machine prompt said that the dirt and dust on the timing machine should be washed thoroughly, the external appearance and smooth holes of each component should be wiped with kerosene, and grease should be injected once, and the exposed part without painting should be coated with butter or anti-rust glue.
壓路機應儲存在枯燥的庫房內，克制存放無關物品及汽油，萬一在雨天露天停放時，停放地上應連接枯燥，用防雨布把它蓋好。更多相關設備問題就來我們網站http://m.yuanchuodian.cn咨詢了解吧!
The road roller shall be stored in a dry warehouse. It is prohibited to store irrelevant items and gasoline. In case of outdoor parking in rainy days, the parking ground shall be connected with dry and covered with waterproof cloth. For more relevant equipment problems, please visit our website http://m.yuanchuodian.cn Ask about it!
公司地址：濟南市商河縣賈莊鎮民營經濟創業園
公司名稱:永誠廣建公路材料（山東）有限公司 
備案號：